ISO 16426 PDF
BRITISH STANDARD BS EN ISO Incorporating Corrigendum No. 1 Fasteners — Quality assurance system The European. Find the most up-to-date version of ISO at Engineering We are looking ISO , it was referenced in a document. The statement that can be found on it is: ISO specifies requirements for a fastener q.
|Published (Last):||18 April 2008|
|PDF File Size:||6.79 Mb|
|ePub File Size:||20.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, parties to agreements based on this International Standard are encouraged to investigate the 16246 of applying the most recent editions of the normative documents indicated below. Copyright Copyright subsists in all BSI publications.
The requirements for such characteristics are assured by means of a suitable monitoring process, based on a written control plan. The customer, upon opening the original packaging, assumes full responsibility for all subsequent traceability. Standards Subsctiption may be the perfect solution. This European Isso shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Mayand conflicting national standards shall be withdrawn at the latest by May This standard is not included in isoo packages.
It is identical with ISO Amendments issued since publication Amd.
BS EN ISO 16426:2002
Subscription pricing is determined by: These normative references are cited at the appropriate places in the text and the publications are listed hereafter.
Contact the Information Centre.
For this reason, corrosion resistance is assured by means of suitable production management measures utilizing in-process control. Your Alert Profile lists the documents that will be monitored. When coating the parts for iiso protection, differences in the local thickness of the coating cannot be avoided and will vary depending on the part size and the coating method, and may cause differences in the local salt spray corrosion resistance.
Foreign or mixed parts can result either from the manufacturer’s production chain or the production chain of another party or from other sources. For undated references the latest edition of the publication referred to applies including amendments.
Need more than one copy? Parts with non-conformities in measurements, geometry and other properties result from unsystematic or systematic process characteristics.
BS EN ISO – Fasteners. Quality assurance system
Endorsement notice The text of ISO Fasteners manufactured under the conditions of this International Standard shall be delivered in manufacturing lots. With an automatic inspection process, usually four or five characteristics are checked simultaneously.
For all other characteristics, the manufacturer may use the quality plan of his choice and the customer shall rely on ISO to evaluate the level of conformance of the purchased fasteners. The work 1626 preparing International Standards is normally carried out through 1626 technical committees. This International Standard specifies requirements which shall be met by the mechanical fastener manufacturers and distributors.
This International Standard outlines the requirements from receipt of raw material through the manufacturing process to delivery at the distributor or the user, who is the installer. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.
It is incorporated by Royal Charter. Annex A iwo this International Standard is for information only. In the kilnuley evtne ttah a borpmel talerign to ti f si,dnuo saelpfni erom teh tneCS larterceratai ta thserdda es igvne olebw.
The BSI copyright date displayed in this document indicates when the document was last issued. If the user considers that the degree to which the characteristic s deviate s from specified requirements will have no significant effect on the assembly or performance of the fasteners in their service application, the user may authorize a written release of the fasteners for completion of production or for shipment, as applicable.
If no parts inspected are found to be non-conforming, the fastener lots may be approved for delivery or use as applicable.
A quality judgement of this characteristic by evaluation of ppm is not possible. In the manufacture of fasteners, a number of production processes are reached by means of cold forming.
BS EN ISO Fasteners — Quality assurance system – MBA智库文档
Users are responsible for its correct application. For details of these and other benefits contact Membership Administration. NOTE 2 The manufacturing lot may be split into a number of manufacturing batches for processing purposes and then reassembled into the same manufacturing lot. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for oso standards. Proceed to Ixo Continue Shopping. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
In addition, the parts are transferred into other vessels many times during the production process, the number of transfer operations depending on the length of the production chain e.